"When laying the floor, more than 20 pieces of boards were just cut a little bit and thrown away, letting me dig a few hundred yuan extra." Recently, consumer Ms. Zhang reported to "New Home Weekly" complaining that her home was on the floor Annoyance encountered during laying. After some investigation, the reporter found that some floor vendors let workers deliberately wear out in order to sell more goods; and the current labor cost for floor laying is calculated based on the floor area used, and some decoration workers are also willing to cooperate with the business to lay out an additional two square meters You can make more money.
Ms. Zhang said that when buying flooring at the time, the merchant indicated that she would pay more for less. In order to unify the color, it is recommended that Ms. Zhang buy more and relax the ratio by about 5%. According to the measurement, the floor area is 86 square meters. Ms. Zhang specially bought a 90 square meter floor for unexpected needs. However, what she did not expect was that when the laying was about to end, the workers asked her to buy two more square meters. The floor of the rice, because the board is not enough, but there are more than 20 boards on the ground with their heads or sides cut, thrown on the ground and scrapped. Ms. Zhang said that she was busy at work, so she trusted the workers and left them with the floor, but when they took the time to see the scene, they found that the workers lacked collaboration and cut the floor at will. Some of the remaining small wooden boards can be used together. But it is necessary to cut the whole board and ask the workers, they said that the floor interface should be aligned, so they need to cut new boards. After the paving was completed, Ms. Zhang made a careful calculation and was shocked: a total of 86 square meters of flooring was paved, 92 square meters were actually used, and the loss rate was 7%. The boards thrown away in vain are distressed. However, it is no longer useful. The floor of more than 300 square meters was spent by workers at least 3 square meters, and they spent nearly a thousand yuan in inadvertent money.
Why is there a loss on the floor, what is the general loss rate? The reporter interviewed the person in charge of Xinwu flooring. According to reports, in the floor laying, because the length and width of each floor are the same, but the length of the wooden board purchased by the consumer cannot be exactly matched with the room to be laid, so some floors are To cut, such as a 90 cm long floor, if 50 cm is used, the remaining 40 cm must be stitched to other places. If it cannot be spliced, it can only be thrown away, which causes loss, as long as the room is neat The rate is about 3%. According to the regulations, after consumers lay the floor, the complete floor can be returned. However, in order to prevent consumers from returning goods, some unscrupulous merchants will increase the consumption to make consumers spend more money, such as deliberately cutting more complete boards. There is also a more concealed method, some floors themselves have "short catty two" situation, such as the original should be 90 cm long board, but some products are only 85 cm, consumers often only count the number of floors when buying , I would n’t think of measuring the length and width of each floor, so the amount of floor actually used is secretly increased.
Relevant experts of the Nanjing Decoration Industry Association told reporters that floor disputes used to focus on the quality of the floor itself or the quality of the floor laying. This phenomenon of "malicious wear and tear" has also begun to rise. In this regard, he reminded consumers to choose reputable merchants and brand floors when buying and paving floors, carefully measure before buying, and pay attention to the progress of paving in the process of paving to prevent pavers from doing tricks. According to the GBT20238-2006 "Code for the Installation, Acceptance and Use of Wooden Flooring" issued by the state, the loss rate of floor paving should generally not exceed 5%. If consumers find that the loss rate exceeds 5%, they can claim compensation from the merchant.
Deep well Plate is an ideal product for sample storage, we have many types of 96 Deep Well Plate, such as 0.5ml elution plate, 1.2ml square well V bottom plate, 2.0ml round well U botttom plate for Hamilton and Nunc machines, 2.2ml square well V bottom and 2.2ml square well U bottom. They can be sterilized under high press, and keep the shape for 20 minutes even the temperature arrives at 121℃,All these characteristics set a new standard for the laboratory.
96 Well Deep Well Plate,2ml Deep Well Plate,Deep Well Microplates,1.2 ml Deep Well Plate,Square Well Plate
Yong Yue Medical Technology(Kunshan) Co.,Ltd , https://www.yongyuecultureflask.com