(1) Under normal circumstances, the valve does not make strength test, but after repair, the valve body and valve cover or corrosion damage valve body and valve cover shall be subjected to strength test. For safety valves, the constant pressure and back pressure and other tests should be consistent with the instructions and the relevant regulations. (2) Akira valve installation should be made for strength and tightness test. Low-pressure valve checks 20%, such as failure should be 100% of the inspection; medium and high pressure valves should be 100% inspection. (3) During the test, the installation position of the valve should be in the direction of easy inspection. (4) Valves of welded connection type may be pressure-tested with conical seal or O-ring seal when pressure test is not performed with shutters. (5) When the hydraulic test will try to exclude the valve air. (6) test pressure to be gradually increased, does not allow rapid, sudden pressure. (7) strength test and sealing test duration is generally 2 ~ 3min, important and special valve should last 5min. Small-caliber valve test time can be shorter, large-caliber valve test time may be longer. During the test, the test time may be extended if in doubt. Strength test, do not allow body and bonnet sweating or leakage phenomenon. Sealing test, the rotor pump valve only once, safety valve, high-pressure valve and other life to the valve to be carried out twice. The test, the low pressure, large diameter of the valve does not matter as well as the provisions of the valve allows leakage to allow a trace of leakage; due to universal valve, power station valves, marine valves and other valves require leakage requirements Should be implemented in accordance with the relevant provisions. (8) Throttle valves shall not be tested for the tightness of the closing parts, but shall be subjected to the strength test and the tightness test at the packing and gasket. (9) During the pressure test, the closing force of the valve only allows one person's normal physical strength to close; it must not be energized by a lever or the like (except the torque wrench). When the diameter of the hand wheel is greater than or equal to 320mm, shut down. (10) The valve with the upper seal should be taken out of packing for sealing test, the seal after the official check to see if leakage. When testing with gas, check the water in the stuffing box. For packing sealing test, the upper seal is not allowed to be in close position. (11) Where a valve with a driving device is used, the driving device shall be used to close the valve to seal the sealing test when testing its sealing property. On the manual drive, should also be closed with the valve seal test. (12) After the strength test and the tightness test, a bypass valve fitted to the main valve shall be tested for strength and tightness at the main valve; the main valve closing member shall also be opened when it is opened. (13) cast iron valve strength test, the use of copper hammer tap valve body and bonnet, check whether there is leakage. (14) When the valve is tested, other valves shall not be allowed to be lubricated on the sealing surface unless the stopcock valve is specified to allow the sealing surface to be oiled. (15) when the valve pressure test, the blind pressure on the valve should not be too large, so as to avoid valve deformation, affecting the test results (cast iron valve too tight if pressed, but also damaged). (16) Valve pressure test is completed, the valve should be promptly ruled out water and wipe clean, should also make test records.
LED Track Light is widely used in supermarket, clothing stores, showroom, shopping mall and so on.
Dilin have many different kinds of led track light to meet customer's requirement such as cylinder led track light, bamboo led track light, zoom ledtrack light, tri-cct led track light, dimmable led track light, Track Linear Light, track Pendant Light and so on.
The various function are avaliable such as : Dimmable, DALI dimmable, 2.4G dimmable, Tuya app control, CCT Tunable and so on.
Fast delivery serivce for led track light : 5-7days for samples, and 15days for bul order.
Led Track Light,Led Track Light Head,Modern Track Lighting,Track Light Fixtures
Jiangmen Dilin Lighting High-Tech Co., Ltd. , https://www.jmdilinlight.com